Free shipping · 60-day returns · 3-year warranty

You have a number. Here is what it means.

Put in your zip and your reading. If you tested your filtered water too, you will get how much your system actually removed, worked out from your own two numbers rather than a specification.

Use these to understand your number rather than to decide whether your water is safe to drink. Safety is a different measurement, and it is further down this page.

Under 50ppm
Very low

Reverse osmosis, distilled or deionised water. Tastes clean, and flat to some people.

50 to 150ppm
Low

Common where the source water is soft.

150 to 300ppm
Moderate

A common range for municipal tap water. Minerals start to show in the taste.

300 to 500ppm
Higher

Often hard water. Scale on kettles and fixtures, stronger taste.

Over 500ppm
Above the EPA guideline

The EPA's 500 mg/L figure is a secondary standard, set on taste and appearance rather than health.

Over 1,000ppm
High

Often brackish water, salt intrusion, or a well worth investigating.

Where Sanavia draws the line

Under 50 ppm

Good

Where we aim. A working RO system should put you here.

50 to 90 ppm

Borderline

Drinkable, and more than we would want in a glass we poured.

Over 90 ppm

Worth filtering

Above where we would leave it. Most untreated tap water here sits above it.

That is a stricter line than the table above, and it is ours rather than anybody else’s. It is not a safety threshold. The EPA’s 500 mg/L figure is about taste and appearance, most municipal tap water in this region sits in the low hundreds, and no TDS number tells you whether water is safe to drink. We sell filters, so take the strictness for what it is: where we think a glass of water ought to end up, not a warning about where yours is now.

For what TDS actually is, how ppm relates to mg/L, and where the EPA’s 500 mg/L figure comes from, the full guide covers it.

One reading is a fact. Two readings are an answer.

A single number off your kitchen tap tells you very little, because there is nothing to compare it with. Take the second glass.

Glass one

Your kitchen tap

What your utility delivers, after it has been through the main and your own plumbing.

Glass two

Your filtered tap

The same water after the system. If you have no system yet, this is the glass you cannot fill, which is its own answer.

The difference is what your system removed, in a figure you measured rather than one we told you. Our installers run the same check before and after every fit.

  1. 1

    Fill a glass from the tap you want to test

    Run the tap for a few seconds, then fill an ordinary glass. Test the water you would actually drink rather than water that stood in the pipe overnight, unless standing water is the thing you are curious about.

  2. 2

    Take the cap off and press ON/OFF HOLD

    The cap covers the probe at the bottom. One press wakes the meter. It reads zero in air, which is correct.

  3. 3

    Dip the probe to the line, not past it

    Far enough to cover the metal contacts and no further. The body is not meant to go under. Give it a stir to shift air sitting against the contacts.

  4. 4

    Wait for the number to settle

    It jumps for a few seconds, then steadies. The steady number is your reading. If it will not settle, stir again: moving water and trapped bubbles are the usual cause.

  5. 5

    Press HOLD and read it

    That freezes the number so you can lift the meter out and read it without crouching over the sink. CLEAR drops the held value and returns to live measurement.

  6. 6

    Rinse the probe and cap it

    Rinse under clean water and dry before the cap goes back on. Minerals dried onto the contacts are the usual reason a meter drifts months later.

Most meters of this kind, including ours, cycle three measurements. Almost everybody only uses the first.

TDS

ppm

Total dissolved solids. Everything dissolved in the water added up as one figure: minerals, salts, metals. This is the reading almost everybody wants.

EC

µS/cm

Electrical conductivity. How readily water carries a current, which rises and falls with dissolved mineral content. It is what the meter physically measures; the TDS number is converted from it. Hydroponics and fish keeping work in EC directly.

Temperature

°C or °F

Conductivity shifts with temperature, so a cold glass and a warm glass of the same water will not read identically. If you are tracking a filter over months, take the reading at roughly the same temperature each time.

Write the first number down

A reverse osmosis membrane does not fail on a particular day. It wears, and as it wears the TDS of the water coming out of it creeps upward.

Take a reading the week your system goes in and write it down somewhere you will find again. That is your baseline. Check every month or two in similar conditions. While the figure sits near the baseline the membrane is working. When it starts drifting up, the membrane is nearing the end of its life, and you will know before anybody notices the taste change.

That turns replacing a filter from a date in the calendar into a decision based on your own water.

What a TDS reading cannot tell you

TDS is a total. It adds up the minerals, salts and metals dissolved in your water and reports one figure, which makes it genuinely good at confirming a filter works and at tracking a membrane as it ages.

It is not a contaminant test, and no TDS meter is. It cannot tell you whether lead, PFAS or disinfection byproducts are present, because those matter at concentrations far below anything it resolves. PFAS is measured in parts per trillion, a million times smaller than the parts per million on your display. A low reading is good news about dissolved solids and nothing more.

See what the EPA has measured near you

Common questions

The EPA's figure is 500 mg/L, and it is a secondary standard, meaning it is set on taste, odour and appearance rather than on health. There is no federal health limit for TDS, because TDS is a total rather than a substance. Water at 450 ppm is not unsafe by that number alone, and water at 20 ppm is not proven clean by it either. Safety is decided by what the dissolved material actually is, which takes a laboratory rather than a meter.

Municipal tap water commonly falls somewhere between 150 and 300 ppm, though it varies widely with the source: river supplies, groundwater and softened water all behave differently. Across the DC metro most utilities draw from the Potomac or the Occoquan, and hardness differs even between neighbouring systems. Your own reading against your own filtered water is more use than any regional average.

Very low TDS is not a hazard in itself. Reverse osmosis, distilled and deionised water all read low by design, and the minerals in drinking water make a small contribution to diet compared with food. The common complaint about low TDS water is taste: some people find it flat. That is a preference rather than a health finding, and it is why remineralising stages exist.

There is no single target, because it depends on what went in. A system fed 400 ppm tap water and returning 20 ppm has done more work than one fed 60 ppm and returning 15. Sanavia aims under 50 ppm. What matters more than the figure on day one is whether it holds: a filtered reading climbing steadily towards your tap reading over months means the membrane is wearing out.

Very few systems produce zero and one that did would be unusual rather than ideal. What matters is that the figure is a small fraction of your tap reading and that it stays where it started. A filtered reading climbing steadily towards your tap reading is the signal to change the membrane.

Usually air. Stir the glass with the probe to shift bubbles sitting against the contacts, then wait a few more seconds. Water that is still swirling from being poured, or a probe resting against the side of the glass, will both make the number wander.

Zero in air is correct, because the meter needs water bridging the contacts. If it stays at zero in water, check the probe is covered and the contacts are clean. A dead display usually means the batteries: it takes two 1.5V LR44 button cells, the same kind used in watches.

For comparing your tap against your filtered water, and watching that filtered figure over months, calibration does not change the answer, because you are reading one meter against itself. The meter is specified to within 2%.

No, and no TDS meter can. TDS is a total measured in parts per million. Lead and PFAS matter at concentrations far below that, with PFAS measured in parts per trillion, a million times smaller. A low TDS reading tells you there is little dissolved material in total. It cannot tell you that what little there is happens to be harmless.

Find out what's in your glass.

Your water test kit is free.

Shop the Hydra